松哥的笔记

爱立信寻呼设置

2013-9-27 lqy 爱立信

PAGLATA:定义LATA寻呼是否被使用,0不使用、1使用。
PAGREPCT1LA:定义当PAGLATA=1时有效，LA内寻呼不成功时，再次寻呼的方法（0：LA内不再寻呼，1：在LA内用TMSI或IMSI再次寻呼，2：在LA内用IMSI重复寻呼，3:重复用IMSI进行）
PAGREP1LA:定义当PAGLATA=0时有效，LA内寻呼不成功时，再次寻呼方法（0：在LA中不再重复寻呼，1：在LA内使用TMSI或IMSI重复PAGING一次，2：在LA内用IMSI重复PAGING一次，3：用IMSI做一次GLOBAL PAGING)
PAGREPGLOB:定义不成功的GLOBAL PAGING之后，再次寻呼方法(0:不在寻呼，1：用IMSI重复一次GLOBAL PAGING)
PAGTIMEFRSRT1LA：第一次区域性寻呼时长。
PAGTIMEFRSTGLOB：第一次全局寻呼时长。
PAGTIMEREP1LA：重复区域性寻呼时长。
PAGTIMEREPGLOB：重复全局性寻呼时长。
对于寻呼时长的设定没有建议值，应该随着网络的不同进行调整。但是一般来讲，第一次寻呼时长要大于第二次，两次寻呼加起来一般不要超过14 秒。
如果第一次寻呼为全局寻呼，那么是否发起第二次全局寻呼将由重复全局寻呼参数决定，
一般我们都会将重复全局寻呼参数设成1，表示用IMSI 发起第二次全局寻呼。寻呼时长由
交换机属性参数PAGTIMEREPGLOB 的值决定参数设置指令如下：
DBTRI;
DBTSC:TAB=AXEPARS,SETNAME=GSMMMSC,NAME=PAGREPGLOB,VALUE=1;
DBTRE:COM;
DBTSP:TAB=AXEPARS,SETNAME=GSM1APTC,NAME=TIMNREAM;
timnream>pagtimefrst1la+pagtimerep1la(or pagtimerepglob)
设置TMSI寻呼是与否： 修改IMSI寻呼为TMSI寻呼指令
dbtsp:tab=axepars,setname=gsmmmsc,name=TMSIPAR;
0 TMSI is not allocated. Note that this setting means that the TMSI is not used. The paging capacity will be decreased if TMSI is not used.
1 TMSI is allocated only on encrypted connection.
2 TMSI is allocated
第一次LA paging失败后，是否进行第二次LA paging寻呼
dbtsp:tab=axepars,setname=gsmmmsc,name=pagrep1la;
Value 0 indicates that paging in one particular location area is not repeated.
Value 1 indicates that paging in one particular location area is repeated once with either TMSI or IMSI.
Value 2 indicates that paging in one particular location area is repeated once with IMSI.
Value 3 indicates that paging is repeated once as global paging with IMSI.
dbtsp:tab=axepars,setname=gsmmmsc,name=pagrepct1la;

This parameter is only valid in case of mobile-terminating calls when the AXE parameter PAGLATA = 1.
The AXE parameter is applicable to ANSI-GSM.
The availability of this AXE parameter depends on commercial agreements.
Value 0 indicates that paging in a location area is not repeated.
Value 1 indicates that paging in a location area is repeated with either TMSI or IMSI.
Value 2 indicates that paging in a location area is repeated with IMSI.
Value 3 indicates that paging is repeated as call delivery LATA paging with IMSI.
DBTSP:TAB=AXEPARS,NAME=PAGLATA;

The AXE parameter indicates whether the non-LATA related or LATA-related paging method is used
Value 0 indicates that LATA paging is not used
Value 1 indicates that LATA paging is used.
第一次Global paging失败后，是否进行第二次Global paging寻呼
dbtsp:tab=axepars,setname=gsmmmsc,name=pagrepglob;
The AXE parameter defines repeating conditions for paging after unsuccessful global paging.
Value 0 indicates that global paging is not repeated.
Value 1 indicates that global paging is repeated once with IMSI.

标签: 爱立信